Better turn to those who know and can) there is a whole science, if you do it badly, the crack will go on
solidator
January 10, 2015 AT 8:24 pm
Best of all is a mini grinder (a circle with a diameter of 2-4 cm.) .. Then process the edges in several stages .. I highly do not recommend scissors
alex_marchenko
January 10, 2015 AT 8:57 pm
I thought about cutting with a hacksaw for metal, I can't even cut the edge, only rides it scratches
lucky83
January 10, 2015 AT 9:00 pm
Scissors don't even think about it. Cut and even and semicircular .. bends the plate .. current grinder.
pavel_drumsss
January 10, 2015 AT 9:00 pm
Allow me to break in)
Is there any difference in how thick the drill should be if you drill a 5mm crack from the edge?
kirill_an
January 10, 2015 AT 9:01 pm
You can cut with scissors, you just need to choose the right angle.
It is better to take a drill 3-4mm
I do not recommend a grinder - the bronze will overheat, and it is not easy to make an even cut with it.
swerus
January 10, 2015 AT 9:02 pm
I cut out the crack with a dremel, time consuming, but quite neatly. I worked it with the same dremel, only with a nozzle with an emery stone.
Ivan_drums
January 10, 2015 AT 9:23 pm
Lathe, plus a grinder and again a lathe, avoid overheating, especially with b20 alloy
a_sharapko
January 11, 2015 AT 3:57 pm
Bulgarian, neat. Take a plate with a smaller diameter, circle it and forward
pavel_drumsss
January 13, 2015 AT 10:43 pm
Drilled!
alex_marchenko
January 13, 2015 AT 10:44 pm
and what you play, does not go further?
pavel_drumsss
January 13, 2015 AT 10:44 pm
Lounge, pop, now I don’t say anything, I drilled it yesterday, I hope it won’t go, I’m not going to hit it stupidly, I gave it to the rappers for a live concert, returned it with a crack, since all these repairs do not affect the sound of the azone, and even with the current ones prices, I will drill until it breaks apart))
alex_marchenko
Better turn to those who know and can) there is a whole science, if you do it badly, the crack will go on
solidator
Best of all is a mini grinder (a circle with a diameter of 2-4 cm.) .. Then process the edges in several stages .. I highly do not recommend scissors
alex_marchenko
I thought about cutting with a hacksaw for metal, I can't even cut the edge, only rides it scratches
lucky83
Scissors don't even think about it. Cut and even and semicircular .. bends the plate .. current grinder.
pavel_drumsss
Allow me to break in)
Is there any difference in how thick the drill should be if you drill a 5mm crack from the edge?
kirill_an
You can cut with scissors, you just need to choose the right angle.
It is better to take a drill 3-4mm
I do not recommend a grinder - the bronze will overheat, and it is not easy to make an even cut with it.
swerus
I cut out the crack with a dremel, time consuming, but quite neatly. I worked it with the same dremel, only with a nozzle with an emery stone.
Ivan_drums
Lathe, plus a grinder and again a lathe, avoid overheating, especially with b20 alloy
a_sharapko
Bulgarian, neat. Take a plate with a smaller diameter, circle it and forward
pavel_drumsss
Drilled!
alex_marchenko
and what you play, does not go further?
pavel_drumsss
Lounge, pop, now I don’t say anything, I drilled it yesterday, I hope it won’t go, I’m not going to hit it stupidly, I gave it to the rappers for a live concert, returned it with a crack, since all these repairs do not affect the sound of the azone, and even with the current ones prices, I will drill until it breaks apart))